Skip to main content

Archive

Show more

Useful Instruction for Diesel Generator Star




After using a diesel generator for a long time, some malfunctions may occur that will cause the generator fail to start. What can you do when it happens?

If diesel generators fail to start, you can analyze the causes from fuel system failure, electric starting system failure, insufficient compression pressure in the cylinder and the low ambient temperature and other factors.

Fuel System Failure

1. Air in the fuel system

This is a common problem that a diesel generator fails to start normally.

Solution: Check whether the fuel oil pipe connector is loose or not, and ensure that the air is cleared from the fuel system. Loosen the bleed screw bolt on the diesel filter, and then use the manual oil pump to pump the fuel until the air bubble is gone.

2. Fuel Line Obstruction

Solution: Check whether the pipeline is smooth or not.

3. Fuel Filter Clogging

Solution: Clean the filter or replace the filter element

4. The Handle Position of Fuel Injection Pump Is Not Correct

Solution: The handle position should be pushed to no-load when starting the diesel generator set. Rotation speed is about 700-900r/min.

5. Fuel Injector Problem Little fuel injection or fuel injection is not atomized   

Solution: Remove the fuel injector, connect it to the high pressure oil pump, pry the fuel injection pump plunger spring and observe the spray condition. If necessary, wash the injection pump.

6. Oil Supply Problem Oil transfer pump doesnt supply oil or the oil supply is brokenly.

Solution: Check whether the oil inlet pipe is leaked or not and the filter screen on the oil inlet pipe connector is blocked or not.

Electric Starting System Failure


1. Battery Power Shortage

The most common failure for diesel generator is battery failure.

Solution: Use the battery with sufficient power, or increase the battery to use in parallel. Replace the new start-up battery if necessary.

2. Circuit Wiring Error or Poor Contact

Solution: Check whether the wiring is correct and reliable.

The compression pressure in the cylinder is insufficient; fuel injection is normal but does not catch fire; or fuel oil inside the exhaust pipe

1. Excessive wear of piston ring and cylinder liner

Solution: Replace the piston ring, and replace the cylinder liner according to the wear condition.

2. Valve leakage

Solution: Check the valve clearance, vlave spring,  as well as  the sealing of the valve guide and seat. If the seal is not good, you should make a repair.

3. Combustion chamber volume is too large

Solution: Check whether the piston belongs to the model, if necessary, measure the combustion chamber volume.

Ambient Temperature Is Low

Solution: According to the actual ambient temperature, the corresponding low temperature measures should be adopted.

A lack of diesel generator maintenance or operation knowledge will undoubtedly result in malfunction. To prevent the malfunction occurring again, it is obvious that daily maintenance of the generating set is very important, which not only helps prolong the service life of the machine, but also reduces the cost. If you want to know more maintenance tips for the diesel generator, the following articles will be helpful.


Learning how to correctly start a diesel generator is not an easy thing. Starting incorrectly, it may have a bad effect on the diesel generator set. It can be said that correct steps are the precondition to guarantee the normal operation of the unit. Then what are the correct steps to start a diesel generator? Through reading this article, you will get the answer.

1. Check whether the water tank is full of water. In winter, check whether the antifreeze is full
2. Check the oil level, fuel level, and radiator water level. If the level is lower than the specified value, it should be added to the normal position.
3. Check whether all the switch position is correct to meet the start requirements.
4. Check whether the diesel genset Emergency Stopbutton on the dashboard is correct.
5. Check whether the outlet switch of the unit is off-position.
6. Check whether the genset preheating is normal. When the indoor temperature is lower than 20 degree Celsius, the electric heater should be opened to preheat the diesel generator set.
7. Make sure there is no oil leakage or water leakage phenomenon. No debris in the genset and exhaust port.
8. Check whether the battery and voltage is normal.
9. Check whether alternator and diesel engine circuit is normal and firm.
10. Check whether the genset controller indicator light is normal.


Comments

Popular posts from this blog

1250kVA Yuchai Electric Power Diesel Generator Powered by Yuchai YC12VC1...

How to Properly Install Diesel Engine

Installing diesel engine is an important part for engine operation. No matter what will you use the engine for, the first thing is to install it on the machine you want to use. Installation of diesel engine is not an easy thing that everyone can do. How to install engine properly is a point for many users to learn. Moreover, properly installing engine is crucial because any mistaken installation step could lead to engine damage and personal hurt. One of the largest challenges of the engine re - manufacturing business is often associated with improper engine installation. We all know that everyone reads all of the literature that comes with each remain  engine – right? Even after reading all of the paperwork technicians still seem to find creative ways to damage the engines performance and longevity. Enough humor – this article will discuss basic diesel engine installation  and how you can prevent premature engine failures. Imagine the most beautiful remanufacture...

High Quality New 800kw Generators