Skip to main content

Archive

Show more

Checking signal Cable Rail Pressure Sensor of Volvo Engine




Checking signal Cable Rail Pressure Sensor of Volvo Engine


Tools:

885675 Break-out cable

88890074 Multimeter

1 Cut the current with the main switch.

2 Disconnect the connector from the sensor.

3 Connect break-out cable 885675 to the cable harness connector to the engine control unit.

4 Use multimeter 88890074 to do resistance measurement against the engine control unit.

NOTICE! Measurement is done to eliminate short circuiting or breaks in the cable to the engine control unit.


Checking injection control pressure sensor

Tools:

885675 Break-out cable

88890074 Multimeter

1 Turn ignition off.

2 Disconnect the connector from the sensor.

3 Connect break-out cable 885675 between the sensor and the engine control unit.

4 Use multimeter 88890074 for voltage measurement.

5 Turn ignition on.

Checking the wiring to the MPROP valve

Tools:

88890074 Multimeter

NOTICE! If any of the measurements shows an abnormal value, check the wiring to and from the Volvo engine interface.

1 Cut the current with the main switch.

2 Remove the connector to the MPROP.

3 Remove connector A from the EMS2.

4 Use multimeter 88890074 to do a resistance measurement against the engine control unit connector A.

 Checking the solenoid in the MPROP valve

Tools:

885675 Break-out cable

88890074 Multimeter

1 Cut the current with the main switch.

2 Remove the connector from the MPROP valve. Connect break-out cable 885675 to the valve.

NOTICE! Do not connect the other end of the adapter cable to the engine cable harness, since

this can cause a measurement error.

3 Use multimeter 88890074 to check the resistance in the solenoid in the MPROP valve.

NOTICE! Measurement is done to eliminate short circuiting or breaks in the MPROP valve.

VODIA Log Parameters

Logging throttle signal with Vodia

To verify the throttle signal on the J1587 bus do as follow:

1 Choose “Log test” under the “Service and maintenance”meny.

2 Choose “MID 128, Accelerator Pedal Position” and “MID 144, Throttle Calibrated Position” and press play.

3 Verify that booth throttle values displayed in percentage by Vodia changes simultaneous while moving the throttle.











Comments

Post a Comment

Popular posts from this blog

Function Of Battery, Breather And Radiator In Diesel Generator

A diesel generator is a diesel powered machine capable of converting mechanical energy to electrical energy. It basically consists of a diesel engine, who's drive shaft is directly connected to something called an alternator. The job of the alternator is to convert the mechanical energy provided to it by the diesel engine to electrical energy. So the alternator consists of 2 windings called the stator winding and the rotor winding. During operation the stator winding is stationary while the rotor winding are performing circular motion (since they are connected to the drive shaft of the diesel engine). Working Of The Alternator: The rotor windings are excited by some DC current so that a magnetic field is produced around the coil. Since it is performing circular motion the magnetic flux linked with it also keeps performing circular motion at the same speed. This magnetic flux is intersected by the stator winding which is fitted around the rotor. According to Faraday...
Post a Comment
Read more

Yuchai Is Super Confident in Its Innovation

Founded in 1951, with 30 wholly-owned, holding and joint-stock subsidiaries, Guangxi Yuchai Machinery Group Co., Ltd. (hereinafter referred to as the Yuchai Group) is an internal combustion engine manufacturing base with the most complete spectrum of products in the country. In recent years, machinery manufacturing industry has been dropped off influenced by domestic and foreign economic situations, especially domestic overcapacity and unreasonable product structure. Reversely, Yuchai has sold over 3 million engines with the annualized revenues amount to RMB 40 billion. Over the years, as China ’ s largest engine R&D manufacturing base, Yuchai adjusts and optimizes its industrial structure and constantly strengthens its capacity for independent innovation. Therefore, the key technology continues to be the top in the sector for further keeping its own top leader in the industry. Innovation-Driven In 2013, seven world-class diesel-engine products for high-s...
Post a Comment
Read more

Technical Parameters of Boduan 500KW Weichai Generator Set 6M33D572E200

  The 6M33D633E200 diesel engine is a special-purpose diesel engine for land-based power generation in the M33 series. It is a new-structure power generation diesel engine with a centrally - located turbocharger developed by Weichai Power Co., Ltd. in 2016. Continuous Power (COP): The maximum power at which the diesel engine can run continuously under a constant load with no limit on the annual operating hours. It is the ISO standard power. Prime Power (PRP): The maximum power at which the diesel engine can run continuously under variable loads with no limit on the annual operating hours. It is an ISO standard power that allows a 10% overload. Standby Power (ESP): The maximum power in a certain variable - power series that the diesel engine can operate for up to 200 hours per year. It is an ISO standard power with limited fuel consumption.   Operating Conditions and Applications of Baudouin  500KW Weichai Generator Set  Diesel Engine Power Classification Operating Co...
Post a Comment
Read more