Skip to main content

Archive

Show more

Increase of Oil Level and Engine Oil Pump Noise of Genset





Diesel generator set oil oil surface height increase and oil pump noise inspection method


The oil level increase and the oil pump noise are common faults in the diesel generator set lubrication system.







1. Increased oil level


Cause
1. The fuel leaks into the oil basin, the plunger of the diesel engine fuel injection pump wears too much, the injector needle is not closed tightly or the needle valve is stuck in the open position; the clearance between the piston, the piston ring and the cylinder is too large, so that Fuel leaks under the cylinder wall to the oil sump.

 2. The water seeps into the oil basin, and the cylinder head gasket is damaged; the cylinder wall comunicating with the water jacket is cracked; the rubber sealing ring between the wet cylinder liner and the cylinder block is not installed correctly or damaged.


Method of exclusion

First, take out the oil gauge to check if the oil is too thin. If you find that the oil level is high and very thin, you should further find the reason to see if there is water or fuel leaking and dilute the oil. The inspection method is as follows:


Draw out the oil gauge and drop a few drops of oil on the paper to observe the oil color and smell. If the oil is milky yellow and has no other odor, it means that the water has entered the crankcase. Check whether the cylinder head gasket is damaged, whether there is crack in the cylinder water channel, whether the rubber sealing ring between the wet cylinder liner and the cylinder block is installed correctly or damaged. .

If there is fuel smell in the oil, start the engine to see if it is working well. If the exhaust pipe emits black smoke after starting the diesel engine, check whether the needle valve of the injector is properly closed. If there is dripping, it should be repaired. If the engine is underpowered at normal operating temperature, check whether the plunger of the fuel injection pump leaks diesel, and whether the clearance between the piston, piston ring and cylinder is too large, and replace or repair.

After checking the repair, release the old oil, clean the lubrication system, and re-add the specified amount of new oil.

Oil pump noise

Phenomenon: When the diesel engine is running, there is noise coming out at the oil magnetic device.

Cause: The oil pump drive gear and the driven gear are excessively worn or improperly gapped.

Inspection and elimination: If there is noise in the oil pump, check it after the diesel engine reaches normal temperature. Touch the screwdriver head near the oil pump, stick the wooden handle to the ear, and repeatedly change the speed of the diesel engine. If you hear a special noise and vibrate very much, it means that the oil pump is noisy. If the sound is not loud and even, it is normal. After long-term use of the oil pump, the gear wear is too large, not only has noise, but also can be observed from the reading of the oil meter. At this time, the reading of the oil pressure gauge is generally low.

How to inspect and repair diesel generator oil pump

Whether the lubrication system in the diesel generator set can ensure good lubrication conditions when the internal combustion engine is working. Although it is related to factors such as whether the oil passage is unblocked and the filter is functioning, the most important and decisive factor is the performance of the oil pump. Is it good? Therefore, during the maintenance of diesel engines. It is reminded that you should repair and repair the oil pump.

1. Common faults of oil pumps
(1) The pressure limiting valve spring is broken and the ball valve is worn.

(2) Wear of the main and passive gear tooth surfaces, gear shafts, and pump body and pump cover.

(3) The tooth surface is peeled off, and the teeth are cracked and broken.

2. Inspection of the main and passive gear meshing clearance

The increase in gear meshing clearance is caused by the friction between the gears of the oil pump gears.

The inspection method is as follows: the pump cover is removed, and the gap between the two teeth is measured by the thickness gauge at three points of the main and passive gear meshing at 120°.

Inspection of the main and passive gear meshing clearance
The normal value of the meshing clearance between the driving gear and the driven gear of the oil pump is generally 0.15-0.35mm. Each model has clear regulations. For example, the 4135 diesel engine is 0.03-0.082, the maximum is not more than 0.15mm; the 2105 diesel engine is 0.10-0.20mm. The maximum is no more than 0.30mm. If the gear meshing clearance exceeds the maximum allowable limit, the new gear should be replaced in pairs.

3. Inspection and repair of gear end clearance

The gap between the main and passive gear end faces of the oil pump and the pump cover is the end face clearance. The increase in the end face clearance is mainly due to the friction of the gear in the axial direction with the pump cover.

4. Inspection and repair of the working face of the oil pump pump cover

The working surface of the oil pump pump cover will be sunken after being worn. The recess cannot exceed 0.05mm. The inspection method is as follows: the thickness gauge is matched with the steel ruler. The steel ruler is placed on the working surface of the pump cover, and then the gap between the working surface of the pump cover and the steel ruler is measured by a thickness gauge. If the specified value is exceeded, place the oil pump pump cover on a glass plate or flat plate and sand it with a valve.

There are two ways to check it.

(1) Fuse method

Place the fuse on the gear surface, install the pump cover, tighten the pump cover screw and then loosen it. Take out the flattened fuse and measure the thickness. This thickness value is the end face clearance. This gap is generally 0.10-0.15mm, such as 0.05-10.11mm for 4135 diesel engine and 0.05-0.15mm for 2105 diesel engine.

(2) Measuring with a thick gauge and a steel ruler

Gear end face clearance = pump cover recession + gap between gear end face and pump body joint surface.

If the end face clearance exceeds the specified value, there are two repair methods.

(1) Grinding the pump body joint surface and the pump cover plane.

(2) Adjust with a thinner gasket.

5. Inspection of the tip clearance

The gap between the top end of the oil pump gear and the inner wall of the pump casing is called the tip clearance. There are two reasons for the increase in the tip clearance.

(1) The gap between the center hole of the driven gear and the shaft pin is too large, causing friction between the top end of the gear and the inner wall of the pump cover, resulting in excessive tooth gap.

(2) The clearance between the oil pump shaft and the bushing is too large.

The inspection method is as follows: a thick gauge is inserted between the top surface of the gear and the inner wall of the pump casing for measurement. The tip clearance is generally 0.05-0.15mm, and the maximum is not more than 0.50mm, such as the 4135 diesel engine is 0.15-0.27mm, and the 2105 diesel engine is 0.03-0.15mm. If the specified allowable value is exceeded, the gear or pump body should be replaced.

Comments

Popular posts from this blog

1250kVA Yuchai Electric Power Diesel Generator Powered by Yuchai YC12VC1...

How to Properly Install Diesel Engine

Installing diesel engine is an important part for engine operation. No matter what will you use the engine for, the first thing is to install it on the machine you want to use. Installation of diesel engine is not an easy thing that everyone can do. How to install engine properly is a point for many users to learn. Moreover, properly installing engine is crucial because any mistaken installation step could lead to engine damage and personal hurt. One of the largest challenges of the engine re - manufacturing business is often associated with improper engine installation. We all know that everyone reads all of the literature that comes with each remain  engine – right? Even after reading all of the paperwork technicians still seem to find creative ways to damage the engines performance and longevity. Enough humor – this article will discuss basic diesel engine installation  and how you can prevent premature engine failures. Imagine the most beautiful remanufacture...

High Quality New 800kw Generators