Skip to main content

Archive

Show more

Debugging methods for 80KW emergency diesel generator

Do you know how to debug 80kw emergency diesel generator? Today Starlight Power tell you the ways.

After finished to assembly 80kw emergency diesel generator, before debugging, we should inspect the genset clearly.
 
The inspection step is as follows:

1.Check whether the surface of the unit is clean; whether the anchor nut, flywheel screw and other moving machine nut are loose, and the problem is promptly tightened.

2.Check whether the clearance of each part is correct. In particular, carefully check whether the clearance of the pressure reducing mechanism of each inlet and exhaust valve meets the requirements.

3.Put each cylinder in the decompression position, turn the crankshaft to check whether the sound of each cylinder is running abnormally, and whether the crankshaft rotates freely, and pump the oil into a friction surface. Then close the pressure reducing mechanism, shake the crankshaft, check if the cylinder is leaking. If the crankshaft is shaken, it feels very laborious, indicating that the compression is normal.

                         

There is large noise during the genset working, debugging methods is as follows:

1.Check that the vent hole on the fuel tank cap is smooth. If there is dirt in the hole, it should be cleaned. Whether the added diesel meets the required grade, whether the oil is sufficient, and the oil switch is turned on.

2.Open the decompression mechanism and shake the crankshaft. Each cylinder should have a crisp injection sound, indicating good fuel injection. If you hear that the fuel is not coming from the oil, there may be air in the oil circuit. At this time, loosen the diesel filter and the bleeder screw of the fuel injection pump to remove the air in the oil circuit.


Starlight series emergency diesel generator cover Cummins, Volvo, Perkins, Yuchai, Shangchai, Deutz, Ricardo, Wuxi etc. Power range is from 20kw to 3000kw. If you are interested, please contact us by sales@dieselgeneratortech.com.

Comments

Popular posts from this blog

New Yuchai engine YC6K600-D30 power for diesel generator 50Hz

Technical Parameters of Boduan 500KW Weichai Generator Set 6M33D572E200

  The 6M33D633E200 diesel engine is a special-purpose diesel engine for land-based power generation in the M33 series. It is a new-structure power generation diesel engine with a centrally - located turbocharger developed by Weichai Power Co., Ltd. in 2016. Continuous Power (COP): The maximum power at which the diesel engine can run continuously under a constant load with no limit on the annual operating hours. It is the ISO standard power. Prime Power (PRP): The maximum power at which the diesel engine can run continuously under variable loads with no limit on the annual operating hours. It is an ISO standard power that allows a 10% overload. Standby Power (ESP): The maximum power in a certain variable - power series that the diesel engine can operate for up to 200 hours per year. It is an ISO standard power with limited fuel consumption.   Operating Conditions and Applications of Baudouin  500KW Weichai Generator Set  Diesel Engine Power Classification Operating Co...

How to know and solve faults of genset voltage transformer

 Today Starlight Power shares the common faults for voltage transformer of diesel generator set. Hope it is helpful to you. 1) The insulation between iron chips is damaged. Fault phenomenon: temperature rises during operation. The possible causes of the failure are: poor insulation between iron chips, bad use of environmental conditions or long-term operation under high temperature, which promote the insulation aging between iron chips. (2) Poor contact between grounding plate and iron core. Fault phenomenon: there is discharge sound between iron core and oil tank during operation. Cause of failure: the grounding plate is not inserted tightly, and the mounting screw is not tightened. (3) The iron core is loose. Fault phenomenon: abnormal vibration or noise during operation. The cause of failure: the iron core clamp is not clamped, and the iron chip is loose. (4) Turn to turn short circuit of winding. Fault phenomenon: during operation, the temperature rises, there is ...