Skip to main content

Archive

Show more

How to Prevent Diesel Generator Sets from High Temperature



With the increase of temperature in summer, the demand for electricity will also increase, so more diesel generators will be used, so what should we pay attention to in the process of using diesel generators in summer? The following is a detailed introduction of the six points for attention when diesel generator sets are used in summer.

1. Good ventilation to avoid high temperature.
The installation place should be well ventilated, the generator end should have enough air inlet, and the diesel engine end should have good air outlet. The air outlet area should be more than 1.5 times larger than the water tank area.

Reminder: diesel generator SET should not run in the sun exposure to high temperature environment, in case the generator block heating too quickly lead to failure.

2. Keep clean

Keep the installation area clean and avoid the presence of corrosive gases and vapors, such as acidic, alkaline, etc. It is best to install fire extinguishing devices.

3. Exhaust smoke unobstructed

In indoor application, the exhaust pipe must be led outside, the diameter of the pipe must be the diameter of the exhaust pipe of the silencer, the elbow of the connected pipe should not exceed 3, in order to ensure the smoke discharge is smooth, and the pipe should be inclined down 5-10 degrees to avoid Rain Water injection; If the exhaust pipe is installed vertically up, a rain shield must be installed.

4. Shockproof

When the foundation adopts concrete, the horizontal degree of the unit must be measured with the horizontal ruler during installation, so that the unit is fixed on the horizontal foundation. Between the unit and the foundation shall be a special shock cushion or bolts with bottom foot.

5. protective ground connection

The generator unit shell must have reliable protective grounding. For the generator which must have neutral point direct grounding, it must be neutral ground by professional personnel, and be equipped with lightning protection device, it is strictly forbidden to use the electric power earthing device to conduct neutral point direct grounding.

6. bilateral switch

The two-way switch between generator and power must be very reliable to prevent power from being sent backwards. The connection reliability of the two-way switch needs to be verified by the local power supply department. Local power supply department inspection approval.

Since the diesel generator set itself produces high temperature when it is in operation, with the increasing of the external temperature in summer, how to prevent the safe use of diesel generator set in the high temperature weather is often concerned by many users. Below by starlight small to introduce the diesel generator summer maintenance method.

1. Ensure sufficient circulating cooling water

First of all, the circulating cooling water in the diesel generator tank should be kept in sufficient condition so that the maximum heat dissipation can be achieved during the operation of the diesel generator.

2. Keep the coolant in place

When the engine is in a cold state, the coolant level shall be added in time if the liquid level is lower than the minimum mark of the expansion tank between the top and lowest marks of the expansion tank. Note that the coolant in the expansion tank cannot be filled and should leave room for expansion.

3. Correct use of closed cooling system

When the engine is working, the coolant vapor enters the expansion tank and then flows back to the radiator after cooling, which can prevent a large amount of evaporation loss of the coolant and raise the boiling point temperature of the coolant. The cooling system should use high quality coolant with anti-corrosion, anti-boiling, anti-freezing and anti-scale, and must be sealed in order to achieve results.

4. Maintain external and internal cleanliness of the cooling system

The radiator of generator set has soil on the outside, oil stain or heat sink will affect the passage of wind when it is deformed due to impact, and the radiator becomes worse, which results in the excessive temperature of the coolant. So the radiator should be cleaned or trimmed in time.

Additionally, the heat transfer of the cooling fluid will be affected by the fouling in the cooling system, when the fouling is accumulated in the sand or oil. The fouling in the cooling system will increase if the poor quality coolant or water is added, and the heat transfer capacity of the fouling is only one-tenth of that of the metal, thus the cooling effect will be worse.

5. Operator standard operation
Because the temperature is high and the operation staff of the diesel generator set are relatively few, at this time, when operating the diesel generator set in the generator room, we must pay attention to safety in order to prevent the water in the water tank of the diesel generator set from opening the pot because of the high temperature. It is possible that water will splatter and hurt people everywhere.





Comments

Popular posts from this blog

New Yuchai engine YC6K600-D30 power for diesel generator 50Hz

Technical Parameters of Boduan 500KW Weichai Generator Set 6M33D572E200

  The 6M33D633E200 diesel engine is a special-purpose diesel engine for land-based power generation in the M33 series. It is a new-structure power generation diesel engine with a centrally - located turbocharger developed by Weichai Power Co., Ltd. in 2016. Continuous Power (COP): The maximum power at which the diesel engine can run continuously under a constant load with no limit on the annual operating hours. It is the ISO standard power. Prime Power (PRP): The maximum power at which the diesel engine can run continuously under variable loads with no limit on the annual operating hours. It is an ISO standard power that allows a 10% overload. Standby Power (ESP): The maximum power in a certain variable - power series that the diesel engine can operate for up to 200 hours per year. It is an ISO standard power with limited fuel consumption.   Operating Conditions and Applications of Baudouin  500KW Weichai Generator Set  Diesel Engine Power Classification Operating Co...

How to know and solve faults of genset voltage transformer

 Today Starlight Power shares the common faults for voltage transformer of diesel generator set. Hope it is helpful to you. 1) The insulation between iron chips is damaged. Fault phenomenon: temperature rises during operation. The possible causes of the failure are: poor insulation between iron chips, bad use of environmental conditions or long-term operation under high temperature, which promote the insulation aging between iron chips. (2) Poor contact between grounding plate and iron core. Fault phenomenon: there is discharge sound between iron core and oil tank during operation. Cause of failure: the grounding plate is not inserted tightly, and the mounting screw is not tightened. (3) The iron core is loose. Fault phenomenon: abnormal vibration or noise during operation. The cause of failure: the iron core clamp is not clamped, and the iron chip is loose. (4) Turn to turn short circuit of winding. Fault phenomenon: during operation, the temperature rises, there is ...