Skip to main content

Archive

Show more

Fault reason of 100kw electric diesel generator

After long-term operation, diesel generator set maybe have various faults. In order to ensure the normal operation of the unit, diesel generator set should be treated in time. How to troubleshoot the generator set? Today Starlight Power mainly talk about fault analysis of 100KW diesel generator set. Hope it is helpful to you.

1.Failure of fuse burnout

a.The stator and rotor windings are in open circuit (one phase is broken) or one phase of power supply is power outage.

b.Wrong connection at the beginning and end of winding outgoing line or reversed connection inside winding.

c.The connection of power circuit is loose and the contact resistance is large.

d.Generator load is over or rotor is stuck.

e.The power is too low in voltage

f.Bearing is stuck

Fault reason of diesel generator

a.Find out the broken point to repair.

b.Check the polarity of winding, judge whether the end of winding is correct.

c.Tighten the loose connection screws, use the multimeter to judge whether the joints are connected falsely, and repair them; if the voltage drop is too large due to the thin power supply wire, should correct them.

d.Reassemble to make it flexible; replace qualified grease.

2.Failure of bearing overheating

a.Too much or too little grease.

b.Bearing and journal or end cover are too loose or too tight.

c.The end cover or bearing cover of the generator set is not installed flat.

d.The coupling between generator set and load is not calibrated or the belt is too tight.

Solution of bearing overheating

a.Add lubricating grease as required (1 / 3-2 / 3 of volume).

b.Replace clean lubricating grease.

c.If it is too loose, it can be repaired with adhesive. If it is too tight, it should be turned. The inner hole of journal or end cover should be grinded to make it suitable.

d.Recalibration and adjust belt tension.

e.Re-calibrate alternator bearing or replace rotor,

3.Abnormal sound during operation

Failure reason

a.Friction between rotor and stator insulating paper or slot wedge.

b.Bearing wear or sand particles and other foreign matters in the oil.

c.Loose stator and rotor core.

d.Wrong connection or short circuit of stator winding.

Solution of abnormal sound

a.Trim insulation and lower wedge.

b.Replace or clean the bearing

c.Maintenance of stator and rotor core

d.Remove scratches, if necessary, small rotor in the vehicle

e.Eliminating stator winding faults

Above information will tell us how to deal with fault of fuse burnout, bearing overheating and abnormal sound in 100KW diesel generators. This is only for reference, when your generators has above faults, if you are not a engineer, please contact a professional person to deal with it.

Starlight Power is not only provide technical support, but also supply many brands of power diesel generator set, such as Cummins, Volvo, Perkins, Deutz, Yuchai, Shangchai, Ricardo, Weichai etc. Power range is from 20kw to 3000kw. Welcome to contact us by email sales@dieselgeneratortech.com.

标签：

Comments

Post a Comment

Popular posts from this blog

Yuchai Is Super Confident in Its Innovation

Founded in 1951, with 30 wholly-owned, holding and joint-stock subsidiaries, Guangxi Yuchai Machinery Group Co., Ltd. (hereinafter referred to as the Yuchai Group) is an internal combustion engine manufacturing base with the most complete spectrum of products in the country. In recent years, machinery manufacturing industry has been dropped off influenced by domestic and foreign economic situations, especially domestic overcapacity and unreasonable product structure. Reversely, Yuchai has sold over 3 million engines with the annualized revenues amount to RMB 40 billion. Over the years, as China ’ s largest engine R&D manufacturing base, Yuchai adjusts and optimizes its industrial structure and constantly strengthens its capacity for independent innovation. Therefore, the key technology continues to be the top in the sector for further keeping its own top leader in the industry. Innovation-Driven In 2013, seven world-class diesel-engine products for high-s...
Post a Comment
Read more

How to Read Alarm Codes From SmartGen Genset Controller

Auto Module Control Panel is the configuration for nobody on duty controlling generators. This kind of panel adopts auto module control system, with large LCD display to show the menu, such as SmartGen controller. Features:   1. SmartGen 6110 can receive remote output signal from ATS and realize auto start and stop of generators. 2. SmartGen 6310 can realize all functions of 6110, add RS232 interface which can communicate with PC to realize remote operation.  3. SmartGen 6410 Auto Mains Failure controller, can realize all functions of 6310, furthermore can detect  ATS and control directly. The alarm of diesel generator controller is not the amount of stop alarm, which does not affect the normal operation of diesel generator. When the alarm occurs, the unit will not stop, and when the alarm conditions do not exist, the amount of warning will automatically disappear.  Today Starlight manufacturer mainly shares alarm codes for diesel generato...
Post a Comment
Read more

How to know and solve faults of genset voltage transformer

 Today Starlight Power shares the common faults for voltage transformer of diesel generator set. Hope it is helpful to you. 1) The insulation between iron chips is damaged. Fault phenomenon: temperature rises during operation. The possible causes of the failure are: poor insulation between iron chips, bad use of environmental conditions or long-term operation under high temperature, which promote the insulation aging between iron chips. (2) Poor contact between grounding plate and iron core. Fault phenomenon: there is discharge sound between iron core and oil tank during operation. Cause of failure: the grounding plate is not inserted tightly, and the mounting screw is not tightened. (3) The iron core is loose. Fault phenomenon: abnormal vibration or noise during operation. The cause of failure: the iron core clamp is not clamped, and the iron chip is loose. (4) Turn to turn short circuit of winding. Fault phenomenon: during operation, the temperature rises, there is ...
Post a Comment
Read more